澳门·威尼克斯人(中国区)官方网站

Pei Wang      Assistant Professor

Sex:

Email: peiwang@szu.edu.cn

Office:

Talent title:

Final degree: Doctor of Engineering

Tel: 86-755-26536224

Advisor qualification: Master Supervisor

Research Interest:

Additive manufacturing, Alloy and compound, Metallic matrix composites, High-temperature ceramics and composites

Undergraduate Course:

Graduate Course:

Education:

1. 2014.09-2018.08  TU Dresden/IFW Dresden    Engineering       Doctor
2. 2011.09-2014.03  Northwestern Polytechnical University  Materials Engineering Master
3. 2007.09-2011.07   Henan University of Science and Technology   Metal Material Engineering    Bachelor

Career:

2018.10-present, Additive Manufacturing Institute, College of Mechatronics and Control Engineering, Shenzhen University

Publication:

1.P. Wang*, J. Eckert, K.G. Prashanth, M.W. Wu, I. Kaban, L.X. Xi, S. Scudino, A review of particulate-reinforced aluminum matrix composites fabricated by selective laser melting, Transactions of Nonferrous Metals Society of China 30 (2020) 2001-2034. (IF: 2.615)
2.P. Wang, A. Gebert, L. Yan, H. Li, C. Lao, Z. Chen, K. Kosiba, U. Kühn, S. Scudino, Corrosion of Al-3.5Cu-1.5Mg-1Si alloy prepared by selective laser melting and heat treatment, Intermetallics 124 (2020) 106871. (IF: 3.398)
3. P. Wang*, C.S. Lao, Z.W. Chen, Y.K. Liu, H. Wang, H. Wendrock, J. Eckert, S. Scudino, Microstructure and mechanical properties of Al-12Si and Al-3.5Cu-1.5Mg-1Si bimetal fabricated by selective laser melting, Journal of Materials Science & Technology 36 (2020) 18-26. (IF: 5.040)
4.P. Wang*, C. Gammer, F. Brenne, T. Niendorf, J. Eckert, Sergio Scudino, A heat treatable TiB2/Al-3.5Cu-1.5Mg-1Si composite fabricated by selective laser melting: microstructure, heat treatment and mechanical properties, Compos. Part B- Eng. 147 (2018) 162-168.( IF: 4.920)
5.P. Wang*, C. Gammer, F. Brenne, K.G. Prashanth, R.G. Mendes, M.H. Rümmeli, T. Gemming, J. Eckert, S. Scudino, Microstructure and mechanical properties of a heat-treatable Al-3.5Cu-1.5Mg-1Si alloy produced by selective laser melting, Mater. Sci. Eng., A 711 (2017) (562–570). (IF: 3.414)
6.P. Wang*, L. Deng, K.G. Prashanth, S. Pauly, J. Eckert and S. Scudino, Microstructure and mechanical properties of Al-Cu alloys fabricated by selective laser melting of powder mixtures, J. Alloys Compd. 735 (2017) 2263-2266 (IF: 3.779)
7.P. Wang*, H.C. Li, K.G. Prashanth, J. Eckert, S. Scudino, Selective laser melting of Al-Zn-Mg-Cu: Heat treatment, microstructure and mechanical properties, J. Alloys Compd. 707 (2017) 287-290.( IF: 3.779)

  • 上一篇:没有了
  • 下一篇:没有了